Aluminum Plate RFQ Checklist for CNC Machining

What to put in an aluminum plate RFQ for CNC work: alloy and temper, form, machining allowance, tolerances, flatness and certificates.
CNC milling machine cutting a metal workpiece

A complete aluminum plate RFQ for CNC work states six things: the alloy and temper, the product form, the dimensions with machining allowance, the thickness tolerance and flatness the shop needs, the standard the material is produced to, and the documents required at delivery. When those items are clear, every supplier quotes the same material and the plate that arrives can go straight onto the machine. This checklist walks through each item for medium and heavy plate, cut blanks and bar in 5xxx, 6xxx and 7xxx alloys.

Start with alloy and temper, not just the alloy number

6061, 6061-T6 and 6061-T651 are three different requests. The alloy number fixes the chemistry, but the temper decides strength and, for machined parts, how the plate behaves when material is removed. Temper designations are defined in EN 515 in Europe and ANSI H35.1 in the US.

For heat-treatable plate in the 6xxx and 7xxx series, the T651 temper is common for machining stock: the plate is solution heat-treated, stress-relieved by controlled stretching and then artificially aged. The stretching step reduces residual stress, which matters when a large share of the plate is milled away, because stressed material can move or bow as it is cut. Non-heat-treatable 5xxx plate such as 5083 is supplied in annealed or strain-hardened tempers such as O, H111 or H321, so the temper still needs to be named.

If the drawing says ‘6061 or equivalent’, settle what equivalent means before you quote. EN AW-6082 and 6061 are often discussed together, but they are different alloys, and swapping alloy or temper needs approval from the part engineer or the end customer.

Alloy familyWhy buyers specify itPoints to confirm in the RFQ
5xxx (e.g. 5083)Non-heat-treatable, good corrosion resistance, stable for base plates and fixturesTemper (O, H111, H321), flatness, whether cast tooling plate is acceptable instead of rolled plate
6xxx (e.g. 6061, 6082)General machined parts with a balance of strength, machinability and corrosion resistanceT651 or T6, EN or ASTM designation, anodizing quality if the part will be anodized
7xxx (e.g. 7075)High-strength parts, tooling and mold componentsExact temper (T651, T7351 and others), available thickness, residual stress, test documents
Milling machine cutting a metal block in a machine shop
Milling a metal block: plate that is stress-relieved and correctly sized leaves less to correct on the machine. Photo: Daniel Smyth / Pexels

Define the form: plate, cut blank or bar

Rolled plate is usually ordered to ASTM B209 or to EN 485 with chemistry to EN 573-3. In both systems plate is the product thicker than about 6 mm; thinner material is sheet. Extruded bar and profiles fall under ASTM B221 or EN 755, and the mechanical properties of bar can differ from plate of the same alloy and temper, so do not mix the two forms on one line item.

Then decide whether you want full plates or saw-cut blanks. Full plates suit shops that nest many parts and cut in-house. Cut blanks save sawing time and reduce scrap handling, but the RFQ then needs a cut size, a saw-cut tolerance and a quantity per size. State which edges must be saw-cut and whether mill edges are acceptable.

Dimensions and machining allowance

List the finished part size and the blank or plate size you want to buy. The difference is the machining allowance: enough stock on each face to skim off the as-rolled surface and bring the part to flatness, and enough on each edge to clean up saw marks. The right allowance depends on part size, the flatness of the incoming plate and your fixturing, so if you are unsure, give the finished size and ask the supplier to propose a blank size.

Worked example: a machined part finishes at 20 x 150 x 300 mm in 6061-T651, 40 pieces. The buyer orders 25 mm plate cut to 160 x 310 mm blanks, which leaves 2.5 mm per face and 5 mm per edge. Each blank is 25 x 160 x 310 = 1,240,000 mm3, or 1,240 cm3. At a density of about 2.70 g/cm3 for 6061, one blank weighs about 3.35 kg, and 40 blanks about 134 kg. The finished part is 900,000 mm3, so roughly 27 percent of each blank becomes chips. The same blank in 7075 (about 2.81 g/cm3) weighs about 3.48 kg, which is why the alloy must be fixed before freight and price are compared.

Tolerances and flatness in an aluminum plate RFQ

Standard thickness, width and length tolerances are tabulated in the product standards: EN 485-3 for hot-rolled and EN 485-4 for cold-rolled products, and the tolerance tables in ASTM B209. Standard tolerances are often wider than buyers expect on thick plate. If your process needs tighter thickness or flatness, say so as a separate requirement rather than assuming it, and expect it to affect the quote.

  • Thickness: standard tolerance per the named standard, or a tightened value you state.
  • Flatness: a value over a stated length, for example per metre or over the full blank.
  • Saw-cut blanks: length and width tolerance on cut edges and squareness, if it matters to your fixturing.
  • Internal soundness: for thick plate in critical parts, ultrasonic inspection to an agreed practice such as ASTM B594 and an agreed acceptance class.

Documents, marking and packaging

Ask for an inspection certificate type 3.1 to EN 10204, showing the chemical composition, mechanical test results and the lot or cast number that also appears on the material. Specify how each plate or blank is marked (alloy, temper, lot, size) so traceability survives sawing. If your customer requires RoHS or REACH declarations, list them in the RFQ instead of requesting them after delivery.

For surface-critical parts, state the finish (mill finish, protective film on one or both faces) and how scratches will be judged. Plates should be interleaved and crated so they cannot slide against each other in transit.

Aluminum plate RFQ checklist

ItemWhat to stateExample
Alloy and standardAlloy designation and the standard it is produced toEN AW-6061 to EN 485 / EN 573-3, or 6061 to ASTM B209
TemperFull temper designationT651
FormFull plate, saw-cut blank or extruded barSaw-cut blanks
DimensionsFinished size and blank or plate sizeFinished 20 x 150 x 300 mm, blank 25 x 160 x 310 mm
QuantityPieces per size, trial or production, call-off plan40 pcs trial, production to follow
Thickness toleranceStandard or tightened valuePer EN 485-3
Flatness and cut toleranceValue and length; saw-cut toleranceAgreed value over blank length
SurfaceFinish, film, scratch criteriaMill finish, film one side
Internal qualityUltrasonic inspection if requiredASTM B594, agreed class
CertificatesCertificate type and contentEN 10204 3.1 with lot number
ComplianceDeclarations neededRoHS and REACH declarations
Marking and packingLabels, interleaving, crateAlloy, temper, lot on each blank
SubstitutionWhether alternatives may be offeredOnly with written engineering approval

Common gaps that cause re-quotes

  • Alloy given without temper, so suppliers quote different products.
  • Finished part size sent without stating the stock size, so allowance is guessed.
  • Plate and bar mixed on one line although they follow different standards.
  • Flatness required on the drawing but not mentioned in the RFQ.
  • Certificate type left open until the material has already shipped.

FAQ

Is 6061-T6 the same as 6061-T651 for machining?

Both are solution heat-treated and artificially aged, but T651 adds stress relief by stretching, which reduces movement when plate is heavily machined. Whether T6 is acceptable for a given part is a decision for the part engineer, so state the temper you need.

Should I send a drawing with the RFQ?

Yes, where possible. A drawing shows the finished size, critical faces and flatness requirements, which helps a supplier propose the right plate thickness or blank size. You can submit a technical drawing directly.

Can I order plate for prototypes before production?

Yes. Say in the RFQ that the order is a trial or sample batch and whether production volumes are expected later, so material, documents and lot traceability can be planned for both stages.


MOOPEC is a Singapore-headquartered industrial metals supplier with service centers in Shanghai and Wuhan, supporting both production orders and small batches for trials and samples. See our medium and heavy aluminum alloy plates for machining and aluminum alloy range, then tell us what you need with your alloy, temper, sizes and document requirements.

Cover photo by Daniel Smyth on Pexels.

Share:

More Posts

REACH and RoHS compliant steel label

REACH & RoHS Compliance for Steel

What REACH and RoHS mean for steel exported to the EU: the 253 SVHC Candidate List, the 10 RoHS substances, China RoHS, ELV, and how to get compliance documents from mills or SGS testing.

Automotive body-in-white parts

Hot Stamping Steel Grades: 22MnB5 to 2,400 MPa

Hot stamping (press-hardening) steel explained: process, chemistry, 22MnB5, Usibor® 1500P, B1500HS, HC950/1300HS, HC1200/1800HS and OEM grades, plus hot gas forming steel up to the 2,400 MPa class.

Send Us A Message